A couple questions with my system.

General car audio discussion area.
User avatar
mohsye
New Member
Posts: 691
Joined: Thu Oct 14, 2004 11:00 am
Location: Kensal, ND
Contact:

A couple questions with my system.

Postby mohsye » Mon Jul 07, 2008 9:54 pm

Ok so last fall i purchased two of the XJ-12 prototype speakers from acoustic visions.

i'm now finally putting them together.

i'm using a 4.25 cubed box @ 29 hz, all just 1 single sheet of 3/4" mdf. using a slot port. now will this be strong enough? will I need to reenforce anywhere with triangular pieces?

next question.

What kind of amplifier should I run to them? I was thinking a hifonics 1206d?

And last but not least.

What size of power wire would I need to run that kind of power for an amplifier?

right now I have 4 guage from knuconcpets, rest of my system at teh moment is in sig.

sorry for the spaced out post.

thanks in advance
User avatar
KU40
Posts: 6461
Joined: Sun Mar 16, 2003 12:02 pm
Location: Lawrence, KS
Contact:

Postby KU40 » Tue Jul 08, 2008 9:02 am

You may want to brace your box a little. Maybe just a couple strips of wood or dowel rods.

I'm not familiar with those subs, what is their VC config? What is your budget? the hifonics wouldn't be bad.

If you're running over 1000 watts I'd do at least 2 guage. I did 1/0 for mine just for a little overkill. Can't hurt, and just trying to minimize that voltage drop to the back as much as possible.
-Nick aka NS1 aka mopey aka speedbump
Alpine CDA-9827
Crossfire CFQ5.2
JL Audio XR 650csi components, Planet Audio TT2300
Crossfire VR404 on factory rear 6x8's until I get them upgraded
SI 15D2 + 3.8 @ 30 hz + Crossfire BMF 1000D = :)
User avatar
mohsye
New Member
Posts: 691
Joined: Thu Oct 14, 2004 11:00 am
Location: Kensal, ND
Contact:

Postby mohsye » Tue Jul 08, 2008 12:39 pm

http://www.soundsolutionsaudio.com/forum/index.php?showtopic=10024&mode=threaded <http://www.soundsolutionsaudio.com/forum/index.php?showtopic=10024&mode=threaded>
*
There are also XJ-12 12" models available!

They have a highish Q of about .9 (system Q, not driver Qts) but in the car that would give you a lot of thump, essentially flat anechoic to 40Hz and with cabin gain that would be insane. Same motor, slightly different parameters. They also look good in 3.5ft^3 tuned to about 20Hz. They would be a good HT sub in that type of enclosure being essentially flat to 30Hz (anechoic) and fall off fairly quick below that point. In-room measurements as a typical company would post they would be good to under 20Hz flat in-room with some good HT excitement in the 30-60hz range.

Parameters on the XJ-12 with VCs in parallel (dual 8s).

Re: 3.95
fs: 31Hz
Qms: 4.35
Qes: .67
Qts: .58
mms: 114g
cms: .233 mm/N
Vas: 83L
BL: 11.4
Eff: 87.7db/1W/1M
xmax: 26-27mm one way
Pmax: Lets say 600W which is conservative. If you thermally fry the thing your doing something very stupid.



That's about all the info I have. Budget is 250~ for an amp. But wouild gladly spend less if it's good enough. Looking at a 2 ohm load
That help you put more?
User avatar
95Honda
Posts: 1691
Joined: Mon Jan 05, 2004 1:00 pm
Location: Germany
Contact:

Postby 95Honda » Tue Jul 08, 2008 2:43 pm

Hmmm, IKE has about 4 pages of Class Ds right now... They also have Orion 600Ds for $99, you could get a pair ( around 300-400 wrms per sub, might not be enough, or may be just right depending on box), just a thought... They also Have Viper 2400s (2400 watts for both subs, might be a little much) for $355.... That is a TON of power...

Lemme think about your box for a day or so and post back, I remember reading about those subs when they first came out.... I was quite interested in them at the time...
http://www.forceaudio.com

Marshall asked me how much it would be to fly to Idaho....
User avatar
mohsye
New Member
Posts: 691
Joined: Thu Oct 14, 2004 11:00 am
Location: Kensal, ND
Contact:

Postby mohsye » Tue Jul 08, 2008 3:00 pm

Any help would be terrific. I might be stuck with the box as I'm in the process of liquid nailing it together. Only have 2 big clamps so it's part by part daily. I know I put one of the xj-12's in 1.4 cubed sealed off only 200-300 watts and it was pretty impressive so I'm thinking around 500 a piece in the ported as it's going to be extremely loud.

I'm wide open for all suggestions. You guys helped me with my last setup and I loved it so thanks again in advance
User avatar
mohsye
New Member
Posts: 691
Joined: Thu Oct 14, 2004 11:00 am
Location: Kensal, ND
Contact:

Postby mohsye » Tue Jul 08, 2008 7:43 pm

Ok, so after some looking over my box with KU40...

It's 5.7 cubes @ 31 hz.

Will I need to put bracing on the front baffle? I'm thinking some triangular pieces to help with the moments being put on the jokes from the weight of the speakers (40 lbs each)

Also for an amplifer...

I was looking at a kicker 1000.1... but at 300 it's a bit pricey.

Can I get anything @ 2 ohm around 800-1200 watts for cheaper?
User avatar
mohsye
New Member
Posts: 691
Joined: Thu Oct 14, 2004 11:00 am
Location: Kensal, ND
Contact:

Postby mohsye » Wed Jul 09, 2008 11:32 pm

The amplifiers from IKE. How dependent are they?

I'm really deciding between something cheaper and the kick 1000.1

I'm debating buying it off ebay with a 2 year warranty from the seller or an actual wholeselling site.

Suggestions?
User avatar
95Honda
Posts: 1691
Joined: Mon Jan 05, 2004 1:00 pm
Location: Germany
Contact:

Postby 95Honda » Thu Jul 10, 2008 12:41 am

Seriously, I have bought about 10 reforbs from IKE and never had a problem. I just bought an MD2N last week. Wife has a Viper600 in the Jetta that was $99 3 years ago, and it has been wanging everyday...

Just browse the class D section, but like I said, you could get a pair of Orion 600ds for $200, I have bought 2 of those already from IKE...
http://www.forceaudio.com



Marshall asked me how much it would be to fly to Idaho....
User avatar
mohsye
New Member
Posts: 691
Joined: Thu Oct 14, 2004 11:00 am
Location: Kensal, ND
Contact:

Postby mohsye » Thu Jul 10, 2008 6:48 am

Ok. That's basically all the info I needed. Think I should go with one of the class D's or go with a kicker 1000.1?

Also, know of any good places to pick up 2 gauge power wire?
User avatar
nismo
Posts: 6120
Joined: Tue Jan 16, 2001 1:00 pm
Location: Greenwood, IN
Contact:

Postby nismo » Thu Jul 10, 2008 10:38 am

Might try partsexpress.com's P3 stuff...or Knukonceptz.com

Eric

Return to “Car Audio”

Who is online

Users browsing this forum: No registered users and 1 guest